Inflatable Hot Tub Not Heating? Prove Whether It Is Slow or Dead (Worksheet)

    Disclosure: As an Amazon Associate, we earn from qualifying purchases.

    Your hot tub is not at temperature and guests arrive tomorrow. The worst thing you can do now is guess — because “slow” and “dead” look identical at a glance and need opposite responses. A slow heater needs time, a cover, and patience. A dead heater (or a dead flow path feeding it) needs a service centre, and every hour spent hoping is an hour you could have spent booking one.

    This article is not another triage tree. Our hot tub troubleshooting guide already has a “won’t heat” decision tree, and our hot tub pump troubleshooting guide covers the pump-side “won’t heat” symptom. What neither gives you is a record sheet: a way to prove, with numbers you measured yourself, whether your heater is working slowly or not working at all. That is what this worksheet is for.

    First, the one fact that stops the commonest misdiagnosis

    Heating time is not a single number. It depends on the starting water temperature and the ambient temperature, and Bestway publishes model-specific reference tables rather than one heating time. That means no article — including this one — can honestly tell you “your tub heats in X hours.” Anyone who does is either quoting one model’s table as if it were universal, or inventing a figure. What you can do instead is measure your own tub’s progress against its own recent behaviour and its own manual’s table, and that measurement is exactly what the worksheet below produces.

    If your tub shows an error code rather than simply failing to heat, stop here and go to the coded-fault guides instead: Bestway Lay-Z-Spa error codes or Intex PureSpa error codes. Codes are brand- and model-specific — never apply an Intex code to a Bestway tub or a salt-system code to a non-salt spa. This worksheet is for the no-code complaint: the display looks normal, the pump seems to run, but the water is not getting hot.

    The worksheet: fill this in before you touch anything

    Copy this table, or just note the same six readings on paper. Do not skip the starting readings — without them, later numbers prove nothing.

    Reading Your value
    Date and time you start
    Current water temperature (from the display, or a thermometer in the water)
    Target temperature you have set
    Cover on or off? (must be on for the test)
    Approximate air temperature / weather (cold, mild, hot; windy or still)
    When was the filter last cleaned or replaced?

    Now set the target, put the cover on, make sure the heater is actually switched on (not just the pump or bubbles), and leave it alone for a fixed period — two hours is a sensible first interval. Then record:

    Reading after 2 hours Your value
    Water temperature now
    Change since the start reading
    Cover still on the whole time?
    Any error code appeared?
    Filter/water-flow state (see checklist below)

    Reading the result: slow, or dead?

    It moved, even a little. If the temperature rose at all over two covered hours with the heater on, the heater is almost certainly working — slowly. Cold fill water, cold air, wind, and a missing or ill-fitting cover all stretch heating time dramatically, and a tub filled with cold water in cold weather can take a very long time to reach temperature. Your job now is to remove the brakes: keep the cover on throughout heating, shield from wind if you can, and check the filter (below). Then repeat the two-hour measurement. Steady upward progress, however slow, is a working heater. If progress is so slow that the tub cannot reach temperature in your climate at all, that is a conversation with the manufacturer about your model’s published table — not a fault you can fix by fiddling.

    It did not move at all. Zero change over two covered hours with the heater on is the line between slow and dead. Before you call anyone, work the owner checklist below in order, because several no-heat causes are owner-fixable and none of them is the heater itself. If you complete the checklist and a second two-hour covered measurement still shows zero movement, you have proved a dead heater or a dead flow path, and the next step is the service centre — not a third measurement, and not opening the unit.

    It fell. If the water got colder, the heater is not running at all, or the tub is losing heat faster than it gains it (cover off, cold wind, very cold air). Check the heater is actually on, check the cover, then run the checklist.

    The owner checklist, in order

    Work these top to bottom. Stop at the first one that fixes the problem, then re-run the two-hour measurement to confirm.

    1. Power and GFCI. Is the tub plugged directly into a grounded socket with no extension cord, and has the GFCI passed its test? A failed GFCI test means do not use the pump at all — see our electrical safety guide for the full boundary. No extension cord, ever, including heavy-duty ones. If the supply is the problem, a qualified electrician is the fix, not a longer lead.

    2. Mode and settings. Is the heater actually switched on, and is the set temperature above the current water temperature? This sounds insulting and it catches more people than any other single cause: standby modes, lock modes, and timer settings all look like a dead heater. Check your manual for your model’s modes — they differ by brand and panel.

    3. Water level. Is the water at the level your manual specifies? Too low, and flow and heating protection can cut in. Top up to the marked range with the pump off, then re-check.

    4. Filter cartridge. A dirty or clogged filter cartridge is a first-check cause of no-flow and not-heating complaints on Intex and Bestway spas, and the manuals list cleaning or replacing the cartridge before deeper diagnosis. Remove it, inspect it, clean it per your manual, or swap in a spare if you have one: [AFFILIATE LINK: replacement filter cartridge for the reader’s model]. Also check the outlet grid and connections are unblocked. If flow returns and heating resumes, you have found it — and you have also learned to check the filter first next time.

    5. Cover. Was the cover on for the whole test? Heating with the cover off in cold or windy weather is like trying to fill a bath with the plug out. If your cover is waterlogged, damaged, or does not fit, heat loss alone can masquerade as a dead heater: [AFFILIATE LINK: thermal cover / blanket for the reader’s model]. Re-run the measurement with a properly fitting cover before concluding anything.

    6. Ambient reality check. Cold air and cold fill water stretch heating enormously. Compare against your model’s own reference table (start temperature plus ambient temperature), not against a number someone quoted online. If your conditions are at the cold end of the table, slow is expected — and our winter-use guide covers cold-weather running in full, including the Freeze Shield behaviour that matters when the heater is holding a low temperature rather than heating to soak temperature.

    The “call support / service centre” threshold

    You have reached it when any of these is true:

    • Two covered two-hour measurements, with the owner checklist completed, show zero temperature movement.
    • An error code appears that your brand’s code guide does not resolve with an owner-level fix.
    • The GFCI fails its test or trips repeatedly.
    • You suspect the heater, pump internals, control board, or wiring.

    At that point, stop. The manuals say to contact the service centre when first checks do not resolve the problem, and producers of this site stop there too: no heater-part replacement, no panel opening, no board diagnosis is offered here. When you call, your worksheet is your best asset — “started at 18°C, set to 38°C, cover on, filter cleaned, two hours, still 18°C, no code” gets you past the first three questions support will ask, and it proves you did the checks rather than guessed.

    The mistakes this worksheet exists to prevent

    • Declaring the heater dead after one uncovered hour. Cover off, cold wind, cold fill: that test proves nothing except that heat escapes.
    • Quoting a universal heating rate. “1–3°F per hour is normal” is not a verified universal figure and does not appear in the verified fact base for this site. Your model’s table, your start temperature, your ambient temperature — those are the only numbers that count.
    • Chasing a code across brands. An Intex saltwater-model E90 means no water flow — a flow problem first, not automatically a heater failure — and it means nothing at all on a Bestway tub. Keep codes inside their own brand’s guide.
    • Replacing parts by guesswork. A new heater element will not fix a clogged filter, and a new filter will not fix a dead heater. The worksheet tells you which one you are looking at before you spend anything.

    What to do with your worksheet after the fix

    Keep it. If the problem recurs, a second worksheet against the first tells you — and support — whether this is the same fault or a new one, and whether heating is getting slower over time (a filter or scale story) or failed suddenly (a component story). And if your tub is slow rather than dead, the hot tub ownership planner puts heating time in its proper context: the running-cost side of ownership, where cover discipline and season are the levers you actually control.

    Related guides: Inflatable Hot Tub Electrics and GFCI: What Owners Need to Know (General Information Only); Hot Tub Filter Cartridges: When to Clean, When to Replace, and How to Tell; Looking After Your Inflatable Hot Tub Cover: Cleaning, Waterlogging, and Storm Care.

    Share.