Hot Tub Filter Cartridges: When to Clean, When to Replace, and How to Tell
Disclosure: As an Amazon Associate, we earn from qualifying purchases.
The filter cartridge is the most-handled consumable in inflatable hot tub ownership, and the most under-explained. Every guide on this site mentions it — the maintenance schedule lists checking it weekly and deep-cleaning it monthly — but none of them tells you how to judge a cartridge: when cleaning is enough, when it is done, and what “done” actually looks like. That judgement is this article.
The stakes are higher than a dirty filter suggests. A dirty or clogged cartridge is a first-check cause of no-flow and not-heating complaints on Intex and Bestway spas, and the manuals list cleaning or replacing the cartridge before deeper diagnosis. A surprising number of “dead heater” and “weak pump” complaints are filter complaints in disguise. If your tub has a flow or heating problem, the filter is the first thing you check — before you suspect anything more expensive.
What the cartridge actually does
The cartridge is a pleated filter medium that water passes through before it reaches the pump and heater. It catches hair, skin, oils, debris, and the fine particulate that would otherwise circulate, settle, and feed water-quality problems. The pleats exist to give a large surface area in a small package — and that surface area is also what clogs. As the pleats load up, flow drops, the pump works harder, heating slows (the heater needs flow to work), and water quality degrades because less water is being filtered per hour. A filter does not fail suddenly; it fades, and the fade shows up as other symptoms first.
The weekly check (two minutes, every week)
With the pump off, remove the cartridge and look at it. You are checking four things:
- Colour and loading: a light grey or tan tint after a week of use is normal. Heavy brown or green discolouration, or a thick visible layer on the pleats, means it needs cleaning now, not at the next scheduled clean.
- Pleat condition: pleats should be separate and flexible. Pleats stuck together, flattened, or torn are not filtering properly.
- Smell: a clean cartridge smells of nothing much. A sour or musty smell means organic loading that a rinse may not fully remove.
- End caps and core: cracks, warping, or a loose core mean the cartridge is structurally done, however clean it looks.
Rinse the cartridge with clean water — a garden hose, working from the inside out so debris is pushed off the pleats rather than driven deeper into them — and refit it. This weekly rinse is the single highest-value habit in filter care: it takes minutes and it prevents the deep clogging that shortens cartridge life.
The deep clean (monthly, or when the weekly rinse stops being enough)
When rinsing no longer restores the cartridge — water still flows weakly, or the pleats stay discoloured after a thorough rinse — it is time for a deep clean. Soak the cartridge in a filter-cleaning solution made for the purpose, following the product’s own instructions for concentration and soak time, then rinse thoroughly until the water runs clear and no cleaning solution remains. Never use household bleach, detergents, or abrasive tools on a cartridge: residues end up in the tub water, and damaged pleats filter worse than dirty ones.
After a deep clean, compare before and after honestly. If flow is restored and the pleats look and feel close to new, the cartridge has more life. If it still looks loaded, feels stiff, or the pleats stay stuck together, cleaning has reached its limit — see the replacement signs below.
Cleaning method and replacement intervals are model-specific, so your manual is the authority for your cartridge type. This article gives you the judgement framework; the manual gives you the specifics for your model.
Clean vs replace: the decision
Clean it when: the cartridge is structurally sound (pleats intact, caps solid, core firm), the loading is surface debris and discolouration that rinsing or soaking removes, and flow is restored after cleaning. A cartridge in this state has life left, and replacing it would be waste.
Replace it when any of these is true:
- Pleats are torn, flattened, or permanently stuck together after cleaning.
- End caps are cracked or the core is loose or warped.
- Flow stays weak after a proper deep clean — the medium is loaded internally, beyond what cleaning reaches.
- The cartridge smells sour or musty even after cleaning, suggesting organic loading inside the medium.
- You cannot remember when it was last replaced and it has survived many cleaning cycles — cartridges are consumables, and there is a point where continued cleaning costs more in flow and water quality than a new cartridge costs.
When you replace, buy for your exact model: [AFFILIATE LINK: replacement filter cartridge for the reader’s model]. Cartridges are not universal, and a close-but-wrong cartridge filters poorly or does not seal.
The rotation trick: keep a spare
The single best filter habit is owning two cartridges and rotating them. One is in the tub; the other is clean, dry, and ready. When the weekly check says the in-use cartridge needs more than a rinse, you swap in the spare immediately and deep-clean the dirty one at leisure — no downtime, no temptation to run a clogged filter “one more week,” and no emergency purchase. Keep a spare on the shelf: [AFFILIATE LINK: spare filter cartridge for the reader’s model]. Rotation also extends each cartridge’s life, because a cartridge that is cleaned and dried properly between uses lasts longer than one that is rinsed in a hurry and refitted wet.
Filter care and the rest of the system
A filter does not work alone. Its life depends on the water around it: balanced water per the chemicals beginners guide loads a filter more slowly than unbalanced water; regular testing with the test strips guide catches the water-quality drift that shows up as filter loading; and a water change on schedule (see when to change hot tub water) resets the whole system, filter included. If you find yourself cleaning the filter constantly, the problem may not be the filter — it may be the water, the bather load, or debris getting in because the cover is off too much. Fix the cause, not just the symptom.
And if you have cleaned or replaced the filter and flow or heating still has not recovered, you have done the first check properly — now go to pump troubleshooting for the next steps, and if those do not resolve it, the manuals say to contact the service centre. A new filter is a diagnostic tool as much as a consumable: it tells you whether the filter was the problem, and that answer is worth the price of the cartridge.
Related guides: Inflatable Hot Tub Not Heating? Prove Whether It Is Slow or Dead (Worksheet); Green Hot Tub Water? The Algae Recovery Sequence, Step by Step.

7 Comments
Pingback: Owning a Saltwater Inflatable Hot Tub: Cell Cleaning, Salt Checks & Codes
Pingback: Hot Tub Not Heating? Slow vs Dead Worksheet to Prove It
Pingback: Reopening an Inflatable Hot Tub After Winter Storage: Step-by-Step
Pingback: Inflatable Hot Tub Cloudy Water: Causes and How to Fix It
Pingback: Inflatable Hot Tub Hard Water: Calcium Scale and White Flakes Explained
Pingback: Inflatable Hot Tub Foamy Water: Causes and How to Fix It
Pingback: Hot Tub Chemicals for Beginners: What to Buy & Skip